Tag Archives: savannah

How to Fix 11 of the Most Common Household Appliance Problems

Garbage Disposal

All disposals have an overload feature that automatically shuts off the power when the motor becomes overloaded and gets too hot. Once the motor cools, simply push the reset button on the side of or under the unit.

On the other hand, if it hums but doesn’t spin, it may have something stuck in it. Switch the disposal off, then try working through it by turning the blades with a special disposal wrench (sold at home centers) or by turning a bottom bolt. Many disposals have an Allen wrench for that purpose, inset on the bottom of the machine.

Lights

When a light goes out or a switch doesn’t work, you should first check the main electrical panel for a tripped circuit breaker. But don’t stop there. Before you change out light bulbs and switches, see if a GFCI outlet (which may be upstream from the troubled light or outlet) has tripped. Sometimes all the bathrooms or the outside lights are powered through a single GFCI located in one bathroom or elsewhere, such as in a basement. Simply push the reset button on the GFCI and you could be back in business.

Refrigerator

If your refrigerator conks out on a hot day and you have a cat or a dog, immediately check the coils for pet hair. Service pros find this problem on half of their refrigerator calls. The coils are the black tube-and-wire grid that cools the fluid in the compressor. A buildup of hair will cause the compressor to overheat and trigger the overload switch. On many fridges, you get to the coils by opening the grille at the bottom of the refrigerator. Then push a coil cleaning brush (sold at home centers) into the coils, pull it back and vacuum it clean.

If the coils are located on the back, pull out your fridge (it’s often on rollers) and brush them off. Bonus: The clean coils will cool more efficiently and save you money on your utility bill! Once the overload switch is tripped, you may have to wait a few hours for it to cool. It will reset itself and turn the refrigerator back on.

Gas Stove

If your stove burner won’t come on, the likely culprit is the spaghetti sauce that boiled over a few days ago. Use a toothbrush to clean off food spills from the igniter. On an electronic ignition stove, it’s a little ceramic nub located either on the stovetop or under the ceramic seal strike plate. Also make sure that the round ceramic seal strike plate is properly seated on the burner.

Electric Range

If your electric stove burner won’t heat, turn the burner off and pull it out from its socket. Then plug it in again and wiggle it around. If it feels loose, remove the burner again and gently bend the burner prongs slightly outward for a tighter connection. Easy does it. You could end up pushing the whole socket out of its bracket.

Standing Gas Pilot Range

To access the ignition system in an older-style standard gas range, pop the lid. It’s usually hinged on the back side. If the pilot flame is out, poke a needle into the pilot hole to clean out soot (be careful not to ream it wider). Brush off any debris and clean the tube that leads from the pilot to the burner. Then relight the pilot.

Oven Controls

Blame it on the technology. It so happens that if you set the “time cook” function, the oven, much like a programmed VCR, won’t turn on until the appointed time. You may have done this inadvertently, but if your digital display reads “hold,” “delay” or “time cook,” then the timer is engaged. You’ll have to clear it first by pushing the “off” button. On ovens with dials, be sure the knob is turned to “manual.”

Washer

When a washing machine cabinet rocks, it makes a horrible racket during the spin cycle. The solution is to simply readjust the legs. Screw the front legs up or down until the cabinet is level. When both legs are solid on the floor, tighten each leg’s locking nut. In most washers, to adjust the rear legs, gently tilt the machine forward and gently lower it down. The movement will self-adjust the rear legs.

Dryer

Our expert repairman responds to many “dryer-not- heating calls” only to find that the machine is set to “fluff air”—a non-heat setting. Avoid the embarrassment. Check the settings first. Another common cause of poor drying is a clogged lint filter. The filter may look clean, but it may actually be covered by a nearly invisible film caused by dryer sheets. This film reduces airflow and forces the thermostat to shut off the heat before your clothes are dry. Test your filter by pouring water into it. If the filter holds water, it’s past time to clean it. Pull out the filter and scrub it in hot water with a little laundry detergent and a stiff kitchen brush.

 Also check the outside dryer vent for any lint that may have built up there. The louver door–style vent covers are notorious for lint buildup, which traps heat and turns the heat off in the dryer. Pull the cover completely off to get to these clogs.

Air Conditioner

If you turn your central air conditioner on, off and then on again in rapid order, chances are you’ll blow a fuse or shut off a circuit breaker or the air conditioner simply won’t respond. That’s because the compressor (in the outdoor condensing unit) may have stopped in a high compression mode, making it difficult to start until the compression releases. Older condensing units may switch the compressor on anyway, which causes the circuit to overload and blow a fuse. Newer, “smarter” condensing units will prevent this blunder by delaying the AC’s “on” function for a few minutes. It’s easy to mistake this delay with a faulty air conditioner. Be patient and give the air conditioner about five minutes to come back on.

 To determine if you have a blown fuse, locate the special fuse block near the outside unit. Pull out the block and take the whole thing to the hardware store. A salesperson can test the cartridge fuses and tell you if you need to replace them.

Another simple reason your AC might not come on: You’ve signed up for a cost discount with your electric company in exchange for limited air conditioning during high-demand periods, and you’re in an “off” period. If you can’t remember, call your electric company to find out. You don’t want to pay the repair technician to drive out and explain this program to you!

Dish Washer

When your dishwasher no longer gets your dishes clean, a food-filled filter is most often to blame. If it’s clogged, water can’t make it to the spray arms to clean the dishes in the top rack. The fix takes two minutes. Simply pull out the lower rack and remove the filter cover inside the dishwasher. (Check your owner’s manual if you can’t spot the filter.) Then use a wet vacuum to clean off the screen.

While you’re there, slide the nearby float switch up and down. If it’s jammed with mac and cheese, you won’t get any water. If the cover sticks, jiggle it up and down and clean it with water.

from: Lifehacker

Maintenance Tips 101

Most tenants are more than happy to leave maintenance to the landlord. After all, maintenance service is a primary benefit of renting. That said, service calls are intrusive. And in the long run, you’ll pay for damage to your unit caused by neglect. Protect your peace of mind and your security deposit by following a few basic apartment maintenance tips.

Keep the Refrigerator Working Efficiently

Dirty coils hold in heat and make your refrigerator’s motor work harder to cool the inside compartments. Keep coils clean by removing the cover from below the door and vacuuming out the dust that has accumulated. While you’re there, remove the drip pan from underneath the coils. Wash it well, and check the drain for clogs before replacing it. Next, check the freezer. It needs to be defrosted if more than 1/4 inch of ice has accumulated on the walls. Don’t chip away at it with a sharp object. Instead, remove the contents to a cooler, place a pan underneath the ice to catch the drips, and either let the ice melt at room temperature or help it along with a blow dryer.

Take Care of the Flooring

Dirt is a floor’s worst enemy. When embedded into rugs and carpets, it wears out the fibers. On harder surfaces, like wood, laminate and vinyl, dirt causes scratches. Place mats inside and outside your door to reduce the amount of dirt tracked into your apartment. Vacuum low-traffic carpets at least once a week; vacuum high-traffic areas more frequently. Protect wood, laminate and vinyl floors by sweeping every day and mopping weekly with a product recommended for the floor type. Use the minimum amount of fluid needed to clean wood and laminate, as saturation damages wood’s finish and causes laminate to warp.

Keep Heat and A/C Dust Free

Preventive maintenance of the heating and air-conditioning units is all about ensuring proper air flow. Vacuum vents before using the units for the first time each year, and then inspect the vents periodically to make sure new dust hasn’t accumulated. Change filters as soon as they become soiled. Finally, keep furniture and window coverings away. In the case of heat vents, this is as much a safety issue as a maintenance one. Don’t turn off your heat or A/C when you leave for the day. Instead, turn the heat down or the A/C up just a few degrees. You’ll actually save more energy by maintaining a steadier temperature.

Prevent Plumbing Problems

Keep drains flowing freely. Avoid pouring oil, coffee grounds or other solids into the kitchen sink. In the bathroom, remove hair from the sink and tub promptly so they’re not washed down the drain. Sink and toilet clogs usually can be unstopped with a plunger. Fill the clogged vessel with water and then push the plunger straight down in a quick, firm motion. You may need to repeat a number of times before the clog is removed.

Know When to Seek Help

Sometimes it’s best to leave the work to the pros. Report malfunctioning appliances, water you can’t turn off and clogs that don’t respond to plunging. Also report broken or missing grout in the bathroom. Grout isn’t just cosmetic–it keeps water from seeping into walls and floors.

 

by Daria Kelly Uhlig, homeguides.sfgate.com